Don't Be Dumb With Power Tools

I'm about to admit I'm stupid but it's with the hope that the lesson I learned yesterday will serve as a warning and prevent the same thing or worse from happening to someone else.
I've been laid up for the most part since yesterday after a run in with an angle grinder. I was out working on the Bug's pan yesterday morning using a wire wheel on an angle grinder to remove the last bit of undercoating. I was sitting on my little Craftsman roller seat and in a brief moment of inattentiveness as I went to move the seat the wheel on the angle grinder made contact with the bare skin of my leg just above the knee while going 12,000 RPM's. The result wasn't pleasant. I now have a three inch or so long abrasive burn and it hurts like hell. I called my doctor almost immediately but luckily it wasn't bad enough to warrant a visit but rather I was advised to clean it thoroughly (which I'd already done) and apply Neosporin and a bandage. I'm also going in next week to get a Tetanus shot since I haven't had one in about ten years. (Something I've been meaning to do for a while.) By this morning it had started to heal and I've been able to leave the bandage off but it's still very painful off and on to the point where I'm walking with a limp at times.
So let this be a lesson to everyone. Don't be dumb with power tools. If I had just taken the time to turn it off yesterday before moving my chair and resuming work it would have saved me a whole lot of hurt.

Summer Vacation At Last!

As of 3:00pm this afternoon I'm officially on summer vacation for the next seven and a half weeks and don't return to work until Monday August 23. This is definitely one of the perks of working in education. Starting tomorrow morning I'll be outside working on the Bug as much as the weather will permit. And at least now I can get in a few hours in the mornings before the temperature gets too high. I'm hoping to make significant progress this summer.

Heat

I'm sad to say I haven't been able to make much progress on the Bug for several weeks now. Richmond has been suffering from extreme heat with high temperatures above 90 degrees something like 20 days out of the past month. The handful of days we had where it was reasonably cool outside about two weeks ago just had to be during the week and when I was sick on top of that. Even with three fans going in the garage it's just been far too hot to get anything accomplished. It doesn't look like the heat is going to let up anytime soon but I'm hopeful after Wednesday of next week when I'm finally on summer vacation that I can start getting some things done early in the morning before it gets too hot outside.

CV3's Summer Show

The local Volkswagen club, Central Virginia Vintage Volkswagens, put on their summer show today at Iron Bridge Sports Park in Chester, Virginia. With around 90 Volkswagens of all models on display and 8 vendors it was the largest show I've ever seen in this area. Some very nice cars were on display and I also picked up some very useful information from various people I spoke with. I hope this

Paint Layers

I spent a little time this evening testing out the random orbital sander I bought a few weeks back on the body of the Bug. I thought this photo of the layers of paint was interesting. The orange at the center is the original color, the cherry red in the center was the color it was originally and the color it will be again eventually, and the top layer is the darker red it is currently.

$40 and a Bump in the Head Later

I installed a ceiling fan in the garage this morning. Lowe's had a 52" contractor grade fan on sale for $20 this weekend and it was too good a deal to pass up. Installing it was pretty simple. There was a single bulb overhead light in the center of the garage and all I had to do was remove that and wire in the fan in it's place. During the process however I managed to drop the fan motor (the piece the blades attach to) while on top the ladder. The seven foot plunge to the floor it took bent it out of shape and resulted in another trip to Lowe's (third of the weekend) to get a replacement. At least it was only $20 and not more. I've since been able to bend the other motor back into decent enough shape so I may actually be able to put another up somewhere to provide additional circulation.

While I was installing the replacement my four year old son was out in the garage watching me work. As I went to reposition the step ladder the round metal motor housing (that goes around the motor and wiring to give it a cleaner look) that I had (stupidly) left on top the ladder fell and landed on the top of my head. After yelling a few choice words my son asks me in a very nonchalant tone of voice, "What's wrong daddy?" "I hurt myself Matthew," I replied. "You need an ice pack?" "Yea, go get daddy an icepack." So he runs into the house. A minute later he and my wife run out to the garage. "You ok? my wife asks, "Matthew ran into the house frantically saying you had hurt yourself and needed an ice pack. I thought you had really hurt yourself." But other than a bump on my head and feeling stupid for it I was fine.

A little bit at a time

This week I've been making progress on the pans slowly but surely. It's taking far longer and more effort than I initially thought it would. One of the problems I've run into is the old body to pan gasket. Initially I tried just using the wire wheel on the angle grinder to remove it (before realizing exactly what it was) but this created a huge sticky mess. Note to anyone trying to remove this in the future: don't use this method because of the aforementioned huge sticky mess it creates. After a little research I went to Lowe's and got a paint scraper and used that tonight. It was much easier and made far less mess. And the angle grinder will make quick work of the leftover residue.

I also started removing the tar board over the tunnel tonight to make sure there's no rust anywhere. So far I've found nothing but I've still got quite a bit of it left to remove. I'm hoping Sunday to finish up cleaning the pan and have it ready for a coat of POR15 early next week.